home

MVR Film Evaporator

home
MVR Film Evaporator
MVR Film Evaporator
Price And Quantity
  • Set/Sets
  • 1
  • Set/Sets
  • 10000.00-500000.00 INR
    Product Specifications
    • evaporation machine
    • evaporate
    • Stainless Steel
    • 80000 Kilograms (kg)
    • Yes
    • Yes
    • PLC Control
    • 380 Volt (v)
    • DC Motor
    • 10000*5000*4500 Millimeter (mm)
    • silver
    Product Description
    Application:

    Mechanical vapor recompression (MVR) evaporator used is used for milk, glucose, organic acid, VC, xylose, pharmaceutical, chemical, biological engineering, environmental industry, waste recycling industry, paper making industry, salt making industry and so on.

    Structure Drawing:

    Structure: MVR evaporator includes pre-heater, heater, pump, separator, vacuum system, compressor system, automatic control system, cleaning system and so on

    Principle: To feed the material from raw material storage tank through feed pump, the preheating system and the heating system into the heater and the separator. To stop feeding when the liquid level reaches the setting height.

    Then to start material circulating pump, the liquid will be circulating in the heater and the separator, to open the steam valve to heat the raw material, when the temperature is reaching the setting temperature, then turn on the vacuum system and compressor, the impeller speed is gradually increasing, then the system is evaporating, at the same time, the raw material is continuously entering from the bottom of the heater, it is like film flow from bottom to up, it is also heated by steam until boiling, the steam is spraying out from the arc guide groove to separator, the steam will be rotating rise along the wall of the separator and exhaust into compressor, the liquid will drop down to bottom of the separator. The temperature of pure steam will rise after compression, this recycled steam can heat the heater again, so it can save energy. The recycled steam will be cooled and became into hot water which flow into pre heater, to heat the raw material which flow into heater and separator, so the whole system maintained at a constant feed, discharge, evaporation.

    Character:

    MVR evaporator is new technology for modern industry

    • MVR Evaporator saving technology is the most advanced of the current international evaporator technology requires only a very small amount of Health and steam (when start up, need a small amount of steam, normal operation, is almost no need for the steam), greatly reduce business operating costs, reduce environmental pollution.
    • As a result of compressors to provide heat, and compared to conventional evaporator, the temperature difference is much smaller, to achieve a moderate evaporation, which greatly improve product quality and reduce fouling.
    • No condenser or only a small area condenser, structure and process is very simple, fully automatic, continuous operation, safe and reliable.
    • Equipment with CIP cleaning within the pipeline can be realized inside cleaning, the entire device easy to operate, no dead ends.
    • The evaporator is a material at low temperatures ( evaporation temperature 45℃-75℃ )and does not generate foam under the state of evaporation, liquid evenly, do not run material, not easy to coking, minimum denaturation for heatinf material

    Parameter:

    Model

    MVR-0.5

    MVR-1

    MVR-1.5

    MVR-2

    MVR-5

    MVR-10

    MVR-15

    Evaporation capacity

    500kg/Hr

    1000kg/Hr

    1500kg/Hr

    2000kg/Hr

    5000kg/Hr

    10000kg/Hr

    15000kg/Hr

    Inlet saturated steam capacity(kg/Hr)

    500

    1000

    1500

    2000

    5000

    10000

    15000

    Inlet saturation temperature (c)

    55.295

    71.631

    82.109

    90

    90

    90

    90

    Outlet temperature (c)

    12.590

    14.145

    15.185

    16.000

    16.000

    16.000

    16.000

    Outlet the saturation temperature (c)

    67.885

    85.776

    97.294

    106.000

    106.000

    106.000

    106.000

    Inlet saturation pressure kPa (A)

    15.975

    33.441

    51.567

    70.117

    70.117

    70.117

    70.117

    Inlet saturation pressure kPa (A)

    28.432

    59.596

    91.921

    125.029

    125.029

    125.029

    125.029

    Compression ratio

    1.780

    1.782

    1.783

    1.783

    1.783

    1.783

    1.783

    Motor power (kw)

    40

    55

    75

    95

    132

    550

    640

    Outlet volume flow (m^3/s)

    0.795

    0.7971

    0.7985

    0.7997

    0.7997

    0.7997

    0.7997

    exhaust velocity(m/s)

    22.736

    22.795

    22.837

    22.87

    22.87

    22.87

    22.87

    Outlet volume flow (m^3/s)

    4X4X10

    6X4.5X12

    8X5.5X14

    8X5.5X14

    9.5X6X15

    12.6X6.5X17

    13.6X7X17


    Order requirement:

    • What is your raw material?
    • How much is original degree of raw material?
    • How much the finished degree of product do you want to get?
    • How much liter do you want to evaporate per hour?
    • When do you need this machine?


    Trade Information
    • shanghai
    • 50 Per Week
    • 90 Hours
    • carton steel
    • GMP
    Related Products












    right arrow
    left arrow
    Contact Us

    2TH XINGLONG ROAD, RUIAN CITY, Wenzhou, Zhejiang, 325200, China
    Phone :+8613958897272